Head Gasket Replacment Experts
A head gasket is a gasket that sits between the engine block and cylinder head(s) in your automobile.
Its purpose is to seal the cylinders to ensure maximum compression and avoid leakage of coolant or engine oil into the cylinders; as such, it is the most critical sealing application in any engine, and, as part of the combustion chamber, it shares the same strength requirements as other combustion chamber components.
An automobile engine is a four cycle internal combustion engine. It uses three circuits of working fluids:
- Combustible air/fuel mixture
- Water based coolant, usually with glycol mixed
- Motor oil for lubrication
These are all vital, but must never be allowed to intermix. Apart from sealing the cylinder, the head gasket also seals water and oil conduits between the head and block. Any connectivity between them will cause engine failure, or significant problems like burning oil (smoke from the exhaust). Blue exhaust smoke may be indicative of oil burning. White exhaust smoke is an indicator of coolant burning, another sign of head gasket wear.
Occasionally, the compression in the cylinder will cause a leak to form in the gasket and the gasket will have to be replaced, or severe damage can take place (a “blown” head gasket). This problem has been exacerbated by the use of aluminum rather than iron cylinder heads; while lighter than iron, aluminum has a much greater thermal expansion rate, which in turn causes a great deal more stress to be placed on the head gasket. Engine makers have responded to this by adding a non-stick coating such as Teflon to the surface of the head gasket.
If the gasket fails, a variety of problems can occur, from compression loss (leading to power reduction, or a rough engine), to exhaust gases being forced into the cooling system, leading to the engine overheating and increased engine wear due to the motor oil being mixed with antifreeze. Coolant can leak into the cylinders, causing the exhaust to issue steam and the catalytic converter to be damaged. If a very large amount of coolant does this, hydrolock can occur, causing extensive engine damage. Sometimes, all that may happen when a head gasket is blown is excessive steam erupting from the tailpipe; yet the engine may act and drive like normal, until all the coolant is gone and the engine overheats. In other occurrences, compression leaks into small spaces between the gasket and either the cylinder head or engine block trap air that is then released when the engine is turned off, which then escape into the coolant and create air pockets. Sometimes, these air pockets can get trapped in the engines coolant thermostat, causing it to stay closed and further the overheating issue, thereby creating still more voids between the gasket and the engine. Air pockets can also cause the engine to expel coolant into the overflow or expansion tank, thereby reducing the amount of coolant the engine has available to stay cool.
A damaged head gasket can allow gases to leak between cylinders.
The condition of a head gasket is typically investigated by checking the compression pressure with a pressure gauge, or better, a leak-down test, and/or noting any indication of combustion gases in the cooling system on a water-cooled engine. Oil mixed with coolant and excessive coolant loss with no apparent cause, or presence of carbon monoxide or hydrocarbon gases in the expansion tank of the cooling system can also be signs of head gasket problems. A good sign of head gasket failure on water-cooled engines is the presence of a substance that resembles mayonnaise in the oil, often to be seen on the dipstick, or oil filler cap. However, the presence of this substance is not conclusive proof of head gasket failure, since oil could mix with the coolant via other routes.
A leaking head gasket can be classified as either external or internal. An external leak can be identified as oil and coolant accumulating underneath the engine. The presence of coolant can be detected by shining a black light on what appears to be an oil leak; the appearance of coolant will show up under the black light. External leaks can also appear as previously described in the oil. An internal leak can usually be diagnosed by excessive coolant accumulating in the expansion tank along with the presence of hydrocarbons in the form of foam. The possibility of vapors or condensation &/or water (from the road or rain) build up (in aftermarket product installation) from an external breather or catch tank from the head (rocker cover) can also cause a somewhat build up of froth or gunk (foam) in the oil but is highly unlikely.
Affinity Auto expert mechanics are both highly trained and experienced in head gasket replacment.
head gasket replacement in Bountiful, UT and surrounding areas
Cities Served with Head Gasket Replacement Services near
Farmington UT | North Salt Lake UT | Woods Cross UT | West Bountiful UT | Salt Lake City UT | Centerville UT | Woods Cross UT | Kaysville UT | Layton UT